So sánh sản phẩm
chọn tối đa 4 sản phẩm
Module 2 kênh giao diện dây rung Campbell Scientific AVW200

Module 2 kênh giao diện dây rung Campbell Scientific AVW200

  • Mã sản phẩm :
  • AVW200
  • Liên hệ
    • Còn 100sp tại 847 Huyền Kỳ, Phường Phú Lãm,
  • Thông tin chi tiết :
  • Chọn số lượng
  • Mua Ngay
  • Thương hiệu
  • Campbell Scientific
Module 2 kênh giao diện dây rung Campbell Scientific AVW200

The AVW200 is a vibrating-wire analyzer module that allows our dataloggers to measure vibrating-wire strain gages, pressure transducers, piezometers, tiltmeters, crackmeters, and load cells. These sensors are used in a wide variety of structural, hydrological, and geotechnical applications because of their stability, accuracy, and durability.
The AVW200 uses vibrating-wire spectral-analysis technology (VSPECT™). VSPECT observes the incoming sensor signal, performs a Fourier transform and a spectral analysis (transforming the time series into indivdual sinusoidal components in the frequency spectrum), and determines the sensor frequency by identifying the largest signal in the acceptable range and disregarding noise.
Benefits and Features
  • Provides better measurements by significantly reducing incorrect readings caused by noise sources
  • Interfaces two vibrating-wire sensors; more sensors may be connected if an AM16/32B multiplexer is used
  • Self-checking diagnostics give continual feedback on sensor condition
  • High resolution—less than 0.001 Hz (industry standard is 0.1 Hz)
  • Low current drain
  • Interfaces both temperature and frequency measurements from vibrating-wire sensors

Detailed Description

The AVW200 uses an innovative spectral-interpolation method for measuring the sensor’s resonant frequency. With the spectral interpolation method, the analyzer module excites the vibrating-wire sensor, measures the response, performs a Fourier transform on the response, and returns the result with a resolution better than 0.001 Hz—all within two seconds. Because spectral analysis can distinguish signal from noise on the basis of frequency content, this method offers improved immunity to competing noise.
The AVW200 analyzer module also provides many self-checking diagnostics such as vibrating-element signal strength, signal-to-noise ratio, vibrating-element signal decay ratio, and incorrect signal response. These diagnostics can be running in the background to give continual feedback of the condition for each sensor.



Number of Vibrating-Wire Sensors Measured Up to 2 vibrating-wire sensors can be connected to the analyzer module. Additional sensors can be measured by using an AM16/32-series multiplexer.
Power Requirements 9.6 to 16 Vdc
Analog Input/Outputs 2 differential (DF) vibrating-wire measurements (V+ and V-) and 2 single-ended (SE) ratiometric resistive half-bridge measurements (T+ and T-) for vibrating-wire sensor's onboard temperature sensor.
Digital Control Ports 3 digital control ports (C1 – C3)
  • C1 functions as an SDI-12 I/O communication port.
  • C2 functions as a Clk output for multiplexer control.
  • C3 functions as a reset output for multiplexer control.
RS-232 Port 1 9-pin RS-232 port (for connecting to a datalogger COM port)
Measurement Resolution 0.001 Hz RMS (±250 mV differential input range; -55° to +85°C)
Measurement Accuracy ±0.013% of reading (±250 mV differential input range; -55° to +85°C)
Input Range ±25 V
Baud Rates Selectable from 1200 to 38.4 kbps. (ASCII protocol is one start bit, one stop bit, eight data bits, and no parity.)
  • Either 128 or 512 kB of SRAM
  • 2 MB of OS Flash
CE Compliance Standards to which Conformity Is Declared IEC61326:2002
Dimensions 21.6 x 11.18 x 3.18 cm (8.5 x 4.4 x 1.25 in.)
Weight 0.43 kg (0.95 lb)

Typical Current Drain @ 12 Vdc

Quiescent ~0.3 mA
Active RS-232 Communication ~6 mA
Measurement ~25 mA


Product Brochures



Giỏ hàng của tôi (0)